Ametek PLA-PLW Programming Manual Uživatelský manuál stáhnout pdf (Strana 29)

ONCE Causes the STEP to advance only one point after each trigger. Triggers that arrive

during a dwell delay are ignored

AUTO Causes the entire STEP to be executed sequentially after the starting trigger, paced

by its dwell delays. As each dwell delay elapses, the next point is immediately executed.

Command Syntax STEP:VOLTage:STATe <NR1>

Parameters 0 | OFF(0) | 1 | ON(1) | 2 | AUTO(2) | 3 | ONCE(3)

*RST Value 0

Query Syntax STEP:VOLTage:STATe?

Returned Parameters <NR1> 0=OFF

1=ON

2=AUTO

3=ONCE

1 2 ... 24 25 26 27 28 29 30 31 32 33 34 ... 73 74

PROGRAMMING MANUAL 1
WARRANTY INFORMATION 3
Contents 5
DESCRIPTION 11
INTRODUCTION 16
CALIBRATION COMMANDS 16
CALibrate:POINt 17
CALibrate:SAVe 17
CALibrate:STATe 17
CALibrate:VALue:VOLTage 18
CALibrate:TRANsient:OFFSet 18
CALibrate:VALue:CURRent 18
CURRENT SUBSYSTEM 19
[SOURce:]CURRent:SLEW:BOTH 21
[SOURce:]CURRent:TLEVel, ITR 22
INPUT COMMANDS 24
STEP COMMANDS 25
[SOURce:]STEP:CURRent:STATe 26
[SOURce:]STEP:POWer[:LEVel] 26
[SOURce:]STEP:POWer:TIMe? 26
[SOURce:]STEP:POWer:STATe 27
[SOURce:]STEP:VOLTage[:LEVel] 28
[SOURce:]STEP:VOLTage:TIMe? 28
[SOURce:]STEP:VOLTage:STATe 28
MEASUREMENT COMMANDS 30
MODE COMMANDS 31
PORT COMMANDS 32
INPUT CONTACTOR COMMANDS 32
POWER SUBSYSTEM 33
[SOURce:]POWer:SLEW:BOTH 35
[SOURce:]POWer:SLEW:NEGative 36
[SOURce:]POWer:TLEVel, PTR 36
RESISTANCE SUBSYSTEM 38
[SOURce:]RESistance:SLEW:BOTH 39
Unit ms 41
RESistance:TWIDth? 41
STATUS COMMANDS 42
STATus:OPERation:NTRansition 43
STATus:OPERation:PTRansition 43
STATus:QUEStionable? 47
STATus:QUEStionable:ENABle 47
SYSTEM COMMANDS 48
SYSTem:CROSs:MODe:STATe 49
SYSTem:CROSs:RANGe:STATe 49
SYSTem:EOS 49
SYSTem:ERRor? 49
SYSTem:EXTernal:CONTrol 51
SYSTem:GPIB:ADDRess 51
SYSTem:GPIB:EOS 51
SYSTem:INPut:BOOT 51
SYSTem:MODel 51
SYSTem:NET:ADDRess 52
SYSTem:NET:DHCP 52
SYSTem:NET:EOS 52
SYSTem:NET:GATewa y 52
SYSTem:NET:STATe 52
SYSTem:NET:SUBNet 53
SYSTem:RANGe 53
SYSTem:SERial? 53
SYSTem:SHORT:STATus? 53
SYSTem:VERSion? 53
TRANSIENT COMMANDS 54
TRIGGER COMMANDS 55
56
UTILITY COMMANDS 57
VOLTAGE SUBSYSTEM 58
[SOURce:]VOLTage:SLEW:BOTH 60
[SOURce:]VOLTage:TLEVel, VTR 61
POWER-ON INITIALIZATION 63
INPUT CURRENT 63
INPUT POWER 64
INPUT RESISTANCE 64
INPUT VOLTAGE 64
PROGRAMMING TRANSIENTS 65
CONTINUOUS TRANSIENTS 66
PULSE TRANSIENTS 67
TOGGLED TRANSIENTS 67
PROGRAMMING STEPS 68
STATE AUTO 69
STATE ONCE 69
(other statements) 70
MAKING MEASUREMENTS 71
SLEW:BOTH <NRf+> 73
SLEW:NEG <NRf+> 73
TLEV <NRf+> 73
TRAN:TWID <NRf+> 73
VOLTAGE CALIBRATION 74
RESISTANCE CALIBRATION 74

Komentáře k této Příručce

Žádné komentáře

Ametek PLA-PLW Programming Manual Uživatelský manuál Strana 29

Komentáře k této Příručce

Související produkty a manuály pro Zařízení Ametek PLA-PLW Programming Manual